Panduan Alecto ADB-19 Bel Pintu
Butuh manual untuk Alecto ADB-19 Bel Pintu Anda? Di bawah ini Anda dapat melihat dan mendownload manual PDF dalam bahasa Indonesia secara gratis. Produk ini saat ini memiliki 0 pertanyaan umum, 0 komentar dan memiliki 0 suara. Jika ini bukan panduan yang Anda inginkan, silakan hubungi kami.
Apakah produk Anda rusak dan panduannya tidak memberikan solusi? Buka Repair Café untuk layanan perbaikan gratis.
Panduan
ADB-19 Installation
Outdoor-unit:
Indoor-unit:
Important Note:
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
● Recycle used batteries following environmental protection practices.
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
● Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
● Recycle used batteries following environmental protection practices.
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
● Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Connecting:
Important Note:
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
● Recycle used batteries following environmental protection practices.
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
● Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1
Accessories List:
● 1 x Receiver ● 1 x Transmitter
● 1 x User Manual ● 1 x Double-sided adhesive
● 1 x 3 volts CR2032 battery for transmitter
Technical Specification:
● Frequency: 433.92MHz+100KHz
● Modulation Type: ASK
● Ring Volume:＞85dB(within 0.5m)
● Channel space: 1 million sets of auto-learning codes
● Receiver bandwidth: ±90KHz
● Reception Sensitivity:＞-105dBm
● Transmitter Power:＜10mW
● Power consumption(Receiver): standby:＜0.3W
● Power consumption(Transmitter): standby:＜5uA working:＜10mA
● Power Supply(Receiver): AC110-240V
● Power Supply(Transmitter): DC 3V (1x CR2032)
● Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
Important Note:
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
● Recycle used batteries following environmental protection practices.
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
● Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1x1x
1x
<10 sec.
Important Note:
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
● Recycle used batteries following environmental protection practices.
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
● Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
Important Note:
● If you do not plan to use the device for a long time, such as at a vacation, please remove the
battery from Transmitter, then put them in a safe place.
● Improperly using a battery may cause it to leak and damage nearby items, and can create the
risk of fire and personal injury. Batteries should not be left in an area where the children can
reach them as they may pose a chocking hazard.
● Recycle used batteries following environmental protection practices.
Transmitter Installation:
● Stick the Transmitter on the wall or the door with
double-sided adhesive tape.
Receiver Installation:
● Plug the Receiver into any socket of AC110~240V power.
2
Battery Installation (Transmitter):
Transmitter uses a 3V CR2032 battery (included).
Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)
and place the battery. Please be well noted with the correct battery polarity. To replace a new
battery, operate in the same way.
Press lightly the battery
holder at side
CR2032 3V Lithium Battery
1
Accessories List:
● 1 x Receiver ● 1 x Transmitter
● 1 x User Manual ● 1 x Double-sided adhesive
● 1 x 3 volts CR2032 battery for transmitter
Technical Specification:
● Frequency: 433.92MHz+100KHz
● Modulation Type: ASK
● Ring Volume:＞85dB(within 0.5m)
● Channel space: 1 million sets of auto-learning codes
● Receiver bandwidth: ±90KHz
● Reception Sensitivity:＞-105dBm
● Transmitter Power:＜10mW
● Power consumption(Receiver): standby:＜0.3W
● Power consumption(Transmitter): standby:＜5uA working:＜10mA
● Power Supply(Receiver): AC110-240V
● Power Supply(Transmitter): DC 3V (1x CR2032)
● Operating Range:＞150m (in the open air)
Names for Parts:
Instruction Manual
Auto-leaning Code Wireless Door Chime
Model No.: QH-861AK
VOL
MODE
CODE
1x
Rating
Beri tahu kami pendapat Anda tentang Alecto ADB-19 Bel Pintu dengan meninggalkan rating produk. Ingin berbagi pengalaman Anda dengan produk ini atau mengajukan pertanyaan? Silakan tinggalkan komentar di bagian bawah halaman.Selengkapnya tentang panduan ini
Kami memahami bahwa menyenangkan memiliki panduan cetak Alecto ADB-19 Bel Pintu Anda. Anda selalu dapat mengunduh panduan dari situs web kami dan mencetaknya sendiri. Jika Anda ingin memiliki panduan asli, kami sarankan Anda menghubungi Alecto. Mereka mungkin dapat memberikan panduan asli. Apakah Anda mencari panduan untuk Alecto ADB-19 Bel Pintu Anda dalam bahasa lain? Pilih bahasa pilihan Anda di beranda kami dan cari nomor model untuk melihat apakah kami menyediakannya.
Spesifikasi
| Merek | Alecto |
| Model | ADB-19 |
| Kategori | Bel Pintu |
| Jenis file | |
| Ukuran file | 1.35 MB |
Semua panduan untuk Alecto Bel Pintu
Lebih banyak panduan untuk Bel Pintu
Bergabunglah dalam percakapan tentang produk ini
Di sini Anda dapat membagikan pendapat Anda tentang Alecto ADB-19 Bel Pintu. Jika Anda memiliki pertanyaan, bacalah panduan dengan cermat terlebih dahulu. Meminta panduan dapat dilakukan dengan menggunakan formulir kontak kami.