ENGLISH
Introduction
Congratulations on your purchase and welcome
to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.
com/welcome.
The Super Lift & Cut system ensures a close and
easy shave every day. For the best result, move the
shaving heads over your skin in both straight and
circular movements.
Replace the shaving heads every two years for
optimal shaving results.
General description (Fig. 1)
A Protection cap
B Shaving unit
C Shaver on/off slide
D Charging light
E Trimmer (all types except HQ6920)
F Trimmer slide (all types except HQ6920)
G Cleaning brush
H Mains cord
I Appliance plug
Important
Read this user manual carefully before you use the
appliance and save it for future reference.
Danger
Keep the shaver and the mains cord
dry (Fig. 2).
Warning
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
Do not use the shaver or the mains cord if it is
damaged.
If the mains cord is damaged, always have it
replaced with one of the original type in order
to avoid a hazard.
Caution
Always put the protection cap on the shaver
to protect the shaving heads when you are
travelling (Fig. 3).
Only use the mains cord supplied.
Charge, use and store the appliance at a
temperature between 5°C and 35°C.
This appliance is not washable. Never immerse
the appliance in water, nor rinse it under the
tap.
Compliance with standards
This Philips appliance complies with all standards
regarding electromagnetic elds (EMF). If handled
properly and according to the instructions in this
user manual, the appliance is safe to use based on
scientic evidence available today.
General
The appliance is equipped with an automatic
voltage selector and is suitable for mains
voltages from 100 to 240 volts.
Charging
Charge the appliance:
before rst use and when you have not used
the appliance for a long time
when the motor stops or starts running slower
When you have charged the shaver for the rst
time and after a long period of disuse, optimise the
battery capacity in the following way:
-
-
-
-
-
-
-
-
-
-
-
1 Fully charge the shaver (see section ‘Charging
the shaver’ below).
2 Empty the battery through normal use
(shaving).
3 Repeat this process 2 more times.
Note: If you optimise the battery capacity in this way,
you can also charge the shaver in between shaves,
even if the battery is not completely empty yet. This
does not damage the battery.
Charging the shaver
1 Put the appliance plug in the shaver (Fig. 4).
2 Put the mains plug in the wall socket.
Note: Make sure the shaver is switched off.
The charging light goes on. (Fig. 5)
3 Charge the shaver for at least 8 hours
(HQ6970/HQ6950/HQ6920) or 1 hour
(HQ6990), but not more than 24 hours.
HQ6990: When the battery is fully charged, the
charging light starts ashing.
HQ6970/HQ6950/HQ6920: The charging light
stays on as long as the shaver is connected to
the mains.
Note: Do not leave the shaver connected to the mains
continuously.
Note: You can also shave without charging. Simply
connect the shaver to the mains.
4 Remove the mains plug from the wall socket
and pull the appliance plug out of the shaver
when the battery is fully charged.
Cordless shaving time
When the shaver is fully charged, it has a cordless
shaving time of up to 10 days.
Using the appliance
Shaving
1 Push the on/off slide upwards to switch on
the shaver.
2 Move the shaving heads over your skin. Make
both straight and circular movements (Fig. 6).
Shaving on a dry face gives the best results.
Your skin may need 2 or 3 weeks to get
accustomed to the Philips shaving system.
3 Push the on/off slide downwards to switch off
the shaver.
4 Put the protection cap on the shaver after
use, to prevent damage (Fig. 3).
Trimming (all types except HQ6920)
You can use the trimmer to trim your sideburns
and moustache.
1 Push the slide upwards to open the
trimmer (Fig. 7).
The trimmer can be activated while the motor is
running.
Cleaning and maintenance
Regular cleaning guarantees better shaving
performance.
This appliance is not washable. Never immerse
the appliance in water, nor rinse it under the tap.
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as petrol or acetone to
clean the appliance.
For easy and optimal cleaning, Philips Shaving
Head Cleaning Spray (type no. HQ110)
is available. Ask your Philips dealer for
information.
,
-
-
-
Note: Philips Shaving Head Cleaning Spray may not
be available in all countries. Contact the Consumer
Care Centre in your country about the availability of
this accessory.
You can also clean the shaver in the following way:
Every week: shaving unit and hair
chamber
1 Switch off the shaver. Remove the mains plug
from the wall socket and pull the appliance
plug out of the shaver.
2 Cleanthetopoftheappliancerst.Usethe
cleaning brush supplied (Fig. 8).
3 Press the release button (1) and remove the
shaving unit (2) (Fig. 9).
4 Clean the inside of the shaving unit and the
hair chamber with the cleaning brush (Fig. 10).
5 Put the shaving unit back onto the
shaver (Fig. 11).
Every two months: shaving heads
1 Switch off the shaver. Remove the mains plug
from the wall socket and pull the appliance
plug out of the shaver.
2 Press the release button (1) and remove the
shaving unit (2) (Fig. 9).
3 Turn the wheel anticlockwise (1) and remove
the retaining frame (2) (Fig. 12).
4 Remove the shaving heads (Fig. 13).
Note: Do not clean more than one cutter and
guard at a time, since they are all matching sets.
If you accidentally mix up the cutters and guards,
it may take several weeks before optimal shaving
performance is restored.
5 Clean the cutter with the short-bristled side
of the cleaning brush (Fig. 14).
Brush carefully in the direction of the arrow.
6 Clean the guard with the long-bristled side of
the cleaning brush (Fig. 15).
7 Put the shaving heads back into the shaving
unit. Put the retaining frame back into the
shaving unit, push it down (1) and turn the
wheel clockwise (2) (Fig. 16).
8 Put the shaving unit back onto the shaver.
Extra thorough cleaning
For extra thorough cleaning, put the shaving
heads in a degreasing liquid (e.g. alcohol) every six
months. To remove the shaving heads, follow steps
1 to 4 described above. After cleaning, lubricate
the central point on the inside of the guards with a
drop of sewing machine oil to prevent wear of the
shaving heads.
Trimmer (all types except HQ6920)
Clean the trimmer every time you have used it.
1 Switch off the shaver. Remove the mains plug
from the wall socket and pull the appliance
plug out of the shaver.
2 Clean the trimmer with the cleaning brush
supplied (Fig. 17).
Tip: Lubricate the trimmer teeth with a drop of
sewing machine oil every six months (Fig. 18).
Storage
1 Put the protection cap on the shaver after
use, to prevent damage (Fig. 3).
Replacement
Replace the shaving heads every two years for
optimal shaving results.
Bergabunglah dalam percakapan tentang produk ini
Di sini Anda dapat membagikan pendapat Anda tentang Philips HQ6970 Pencukur. Jika Anda memiliki pertanyaan, bacalah panduan dengan cermat terlebih dahulu. Meminta panduan dapat dilakukan dengan menggunakan formulir kontak kami.